Popp Power Plug


Popp Power Plug was developed to control your outdoor lighting via Z-Wave. It is powered by Popp Z-Wave technology.


Before purchasing make sure to contact your Z-Wave Gateway/Controller manufacturer to determine if this device is compatible, typically most Z-Wave gateways will be generically compatible to Switch type devices. The technical specifications of Power Plug can be viewed at that link.


Familiarize yourself with your Power Plug.


  1. Status LED
  2. Info LED
  3. Network button and On/Off


This device can utilize applications up to 3200W in power for most plugin appliances. 



Quick start.

 

Getting your Power Plug up and running is as simple as plugging it into a wall socket and linking it to your Z-Wave network. The following instructions tell you how to add your Power Plug to your Z-Wave network using an existing gateway. 


Using an existing gateway:


1. Place your gateway or controller into Z-Wave pair or inclusion mode. (Please refer to your controller/gateway manual on how to do this)

2. Press the Network button and On/Off on your Switch 3x times within 2 second.

3. Your gateway should confirm if Power Plug is successfully included into your network.

 

LED Indicator Status.

 

By default this LED is controlled by Smart Power Plug status. 


Default LED Usage:

  • When Switch is in an OFF state, the LED will remain OFF.
  • When Switch is in an ON state, the LED will light up GREEN.
  • When Power Plug is in inclusion mode, the LED will flashes white
  • When Power Plug is in exclusion mode the LED will light up white


Product Usage.


The device is able to switch electric loads up to 3500 W and can be switched wirelessly or using the local button. This switch can report Voltage, Current, or Power reports.


Wireless Operation via Z-Wave.

The local control of your Power Plug can be controlled by most Z-Wave gateways. Your Z-Wave gateway/controller will need to support this switch at least generically (support for generic switches).


This device should show up as an ON/OFF device in your Z-Wave gateways interface.

Local Operation.
The local button allows you to control the switch manually. A short press on the button toggles the switch ON or OFF.


Energy Reporting.

Your Z-Wave gateway must support the Meter Command Class in order to view Voltage, Current, or Power (Watt) reports from Power Plug. If your gateway does not support the Meter Command Class in Z-Wave, you will not be able to see these reports.



Advanced functions.


Removing your Power Plug from a Z-Wave network.


Your Power Plug can be removed from your Z-Wave network at any time.You’ll need to use a Z-Wave primary controller to do this and the following instructions which will tell you how to do this using your existing Z-Wave Network.


This method can be used with any Primary Z-Wave Controller even if it is not directly paired to Power Plug.


Using an existing gateway:


1. Place your gateway or controller into Z-Wave unpair or exclusion mode. (Please refer to your controller/gateway manual on how to do this)

2. Press the LED Indicator ON/OFF Button on your Switch 3x times within 2 second.

3. Your gateway should confirm if Power Plug is successfully excluded from your network.


Association Groups.

Group Association is a specific function in Z-Wave that allows you to tell Power Plug who it can speak to. Some devices may only have 1 group association meant for the gateway, or multiple group associations that can be used for specific events. This type of function isn't used too often, but when it is available, you may be able to use it to directly communicate to Z-Wave devices instead of controlling a scene within a gateway which can have unforeseen delays.


Some gateways have the ability to set Group Associations to devices that have these special events and functions. Typically this is used to allow your gateway to update the status of Power Plug instantly.


By default, your primary gateway should have been associated to Power Plug automatically during the pairing of your Switch. For any case you have a Secondary Z-Wave Controller, you'll need to associate it to your Power Plug in order for your secondary controller to update its status.


Group NumberMaximum NodesDescription
11Control other plug or lights on/off


Configuration Parameters.


Parameter 1: Condition after power failure
Size: 1 Byte, Default Value: 0

SettingDescription
0Always Off
1Always On
2Last status


Other Solutions


Technical specifications of Power Plug

German user guide